LTE Support

Releases and Updates

ATCA Tester

Release Version 3.3.0.3b

Date of Release: September 03, 2013

New features in this release:

A) 27 new test cases added to support the HPM.2 (LAN-Attached IPM Controller) :

  • HPM.2 Req 3.1 Get HPM.x Capabilities command support
  • HPM.2 Req 3.2 Get HPM.x Capabilities with other Identifier value
  • HPM.2 Req 3.3 Get HPM.x Capabilities provide IPMI LAN Channel Mask
  • HPM.2 Req 3.5 Response Byte following LAN Channel Mask Absent
  • HPM.2 Req 3.7 OEM LAN Parameters start location
  • HPM.2 Req 3.11 Get ATCA Extended Management Resources command
  • HPM.2 Req 3.12 Completion Code Invalid command to Get ATCA Extended Management Resources
  • HPM.2 Req 3.25 M0 to M1 hot swap event
  • HPM.2 Req 3.27 Version Change event on change in E-Keyed interfaces
  • HPM.2 Req 3.29 Extended Inactive State Management bit
  • HPM.2 Req 3.32 Extended Management State unchanged upon Warm Reset
  • HPM.2 Req 3.36 Set ATCA Extended Management State command
  • HPM.2 Req 3.37 Get ATCA Extended Management State command
  • HPM.2 Req 3.58 Extended Get Port State command support
  • HPM.2 Req 3.65 Extended Inactive State Link remains Enable
  • HPM.2 Req 3.97 LAN Configuration Parameters
  • HPM.2 Req 3.98 Maximum Inbound Payload Size
  • HPM.2 Req 3.99 Maximum Outbound Payload Size
  • HPM.2 Req 3.119 Support of Get Dynamic Credential command
  • HPM.2 Req 3.120 Data Format of Get Dynamic Credential command
  • HPM.2 Req 3.130 Dynamic Sessions bit
  • HPM.2 Req 3.141 Implicit LAN bridging is enabled by default
  • HPM.2 Req 3.142 Get Session Handle For Explicit LAN Bridging
  • HPM.2 Req 3.145 Poll for completion status
  • HPM.2 Req 3.149 Completion Code D5h for LAN bridging disable
  • HPM.2 Req 3.150 Completion Code 82h for HPM.2 non-complaint target IPMC
  • HPM.2 Req 3.155 Advanced discovery mechanism support

B) 9 new test cases added to support the HPM.3 (DHCP-Assigned Platform Management Parameters) :

  • HPM.3 Req 2.2 HPM.3 compliance Controllers is compliant with HPM.2
  • HPM.3 Req 2.3 Get HPM.x Capabilities command support
  • HPM.3 Req 2.4 Get HPM.x Capabilities with other Identifier value
  • HPM.3 Req 2.5 Revision Identifier value 01h
  • HPM.3 Req 2.10 Get IP Address Source command
  • HPM.3 Req 2.12 IP Address Source 00h
  • HPM.3 Req 2.90 OEM LAN Parameters Block Revision Number 01h
  • HPM.3 Req 2.103 DHCP Configuration Record
  • HPM.3 Req 2.104 AMC Carrier DHCP Configuration Record

Release Version 3.2.0.6

Date of Release: December 07, 2012

This is a maintenance version and contains a number of bug fixes over the earlier version 3.2.0.5

Release Version 3.2.0.5

Date of Release: October 11, 2012

This is a maintenance version and contains a number of bug fixes over the earlier version 3.2.0.4

Release Version 3.2.0.4

Date of Release: June 25, 2011

This version of ATCA Tester is fully conformant with PICMG Specification PICMG® 3.0 Revision 3.0 and it also implements the Advanced E-Keying requirement based on the PICMG® 3.1 Revision 2.0. Nineteen new test cases are included in this version.

Release Version 3.1.0.4

Date of Release: December 09, 2011

There are many bug fixes covering more than 50 test cases

Beta Release Version 3.1.0.2

Date of Release: May 27, 2011

Ten new test cases have been added in this version. The new test cases tests Watchdog Timer Commands Support, Board E-Keying, SDR Requirements, BLUE LED Blinking, Sensor Commands And SDR Consistency, Sensor Event Messages Disable Bit, Sensor Events Mask, Sensor Scanning Disable Bit, Threshold Based Sensors, Backplane E-Keying.

Beta Release Version 3.0.0.20

Date of Release: March 8, 2011

The new feature in this release is that the Setup dialog allows the user to set the timeout for a response to an IPMI command. Also few tests have been modified in this version in order to resolve the issues reported in the earlier version.

Release Version 3.0.0

Date of Release: August 31, 2010

This is a maintenance version and contains a number of bug fixes over the earlier version 3.0.0.

Beta Release Version 3.0.0

Date of Release: April 12, 2010

This version has a Windows based GUI and is based on the PICMG 3.0 Rev 3.0 ATCA base specification and the CP-TA ICD (Interoperability Compliance Document) and TPM (Test Procedures Manual) v 3.0, all tests have been restructured accordingly. It includes more than 375 test cases. This version helps to ensure that ATCA systems meet the compliance and certification requirements of CP-TA's ATCA certification program.

Maintenance Release Version 2.2.25

Date of Release: June 12, 2009

This release includes a command line option ("-t" or "--timeout") specify the response timeout of all commands. It also contains a number of bug fixes over version 2.2.2.

Maintenance Release Version 2.2.2

Date of Release: November 13, 2008

This release incorporates some changes based on discussions with CP-TA. This release contains a number of bug fixes over Release Version 2.2.1.

Maintenance Release Version 2.2.1

Date of Release: September 23, 2008

This release contains HPM beta test cases and a number of bug fixes over Beta Release Version 2.2.1.

Beta Release Version 2.2.1

Date of Release: May 12, 2008

This is a maintenance version and contains a number of bug fixes over version 2.2.0.

Maintenance Release Version 2.2.0

Date of Release: February 12, 2008

This version adds a new test category for HPM.1 testing. This test category contains 5 IPMC test cases and 5 MMC Test cases. Also this version implements some of the critical differences in PICMG3.0 R3.0 manageability section.

Maintenance Release Version 2.2.1

Date of Release: November 26, 2007

This is a maintenance version and contains a number of bug fixes over version 2.1.0.

Maintenance Release Version 2.1.0

Date of Release: November 07, 2007

This version of ATCA Tester is compatible to PICMG 3.0 R2.0 AdvancedTCA Base Specification ECN-002 May 26, 2006.

MicroTCA Tester

Maintenance Release Version 1.5.0

Date of Release: July 29, 2010

It supports CLI mode of test execution for interactive tests and resolves the reported issues of v 1.5.0.5

Maintenance Release Version 1.5.0

Date of Release: April 1, 2010

This version includes Context sensitive help and Command Line Interface (CLI)

Maintenance Release Version 1.4.0

Date of Release: May 19, 2009

This release contains a number of bug fixes over Release Version 1.3.0

New Release Version 1.3.0

Date of Release: February 25, 2009

This version supports license based on USB security key.

Maintenance Release Version 1.2.0

Date of Release: December 04, 2008

The test coverage of this automated test suite has been increased significantly by adding 43 new test cases. This release also contains a number of bug fixes over Release Version 1.1.0

Maintenance Release Version 1.1.0

Date of Release: August 06, 2008

This release contains a number of bug fixes over Release Version 1.0.0

First Release Version 1.0.0

Date of Release: May 13, 2008

This release includes a command line option ("-t" or "--timeout") specify the response timeout of all commands. It also contains a number of bug fixes over version 2.2.2

AMC Tester

Release Version 1.4.0.4b

Date of Release: September 13, 2013

New in this release

1. The total number of Insertion/Extraction cycle of AMC card is reduced by restructuring the interactive test scripts.

2. 7 new test cases are added by combining some old test cases having Insertion/Extraction cycle.

  • REQ_3_114b_116_118_119b_120_122_124b_195_COMBINED_TEST
  • REQ_3_162_and_REQ_3_163_COMBINED_TEST
  • REQ_3_22_and_REQ_3_54_COMBINED_TEST
  • REQ_3_36_REQ_3_37_and_REQ_3_101_COMBINED_TEST
  • REQ 3.43, 3.44, 3.45 and 3.67 Combined Test
  • REQ 3.57 and REQ 3.58 Combined Test
  • REQ 3.59 and REQ 3.60 Combined Test

Release Version 1.4.0.1b

Date of Release: July 31, 2012

In this new version 51 new test cases have been added to support MTCA.4 implementation. Command Line Interface is also implemented in this version for running tests.

Release Version 1.3.0.5

Date of Release: December 21,2011

In this new version 5 HPM test cases have been added. Also in this version 8 issues have been resolved covering more than 15 test case scenarios and some of the debug messages have been modified.

Maintenance Release Version 1.3.0

Date of Release: May 29,2009

This is a maintenance version and contains a number of bug fixes over the earlier version.

New Release Version 1.2.0

Date of Release: February 18, 2009

This version supports license based on USB security key.

New Enhanced Release Version 1.1.0

Date of Release: October 24, 2008

This release has around 50 additional test cases , which increases the coverage of the tester considerably. The AMC tester now covers all testable requirements.

First Release Version 1.0.0

Date of Release: August 12, 2008